Description: for SpeedyBee F405 V3 Flight Controller MCU:STM32F405 IMU (gyroscope):BMI270 USB Port Type:Type C Barometer:Internal OSD Chip:AT7456E Chip BLE Bluetooth:Support, for parameter tuning DJI Air Unit Connection Method:Support 6pin socket direct connection, welding wire connection two ways MicroSD Card Slot Blackbox:Support, please use a MicroSD card of SDSC/SCHC type below 4GB, which must be formatted in FAT16/FAT32 format. Do not use SDXC type cards. Note: Betaflight only supports up to 4GB Galvanometer Input: Supported. When paired with for SpeedyBee BLS 50A ESC, please set Scale=386, Offset=0 Betaflight camera parameter adjustment pad: Support (front CC pad) Power input:3S - 6S Lipo (Through the 8pin interface on the back or the G, BAT pins/pads in the pads) 5V BEC Output : 9 groups of 5V output, (4 +5V pads on the front and 1 BZ+ buzzer pad, and one +5V pad on each of the 4 corners for external LED lights), the total current output is 2A 9V BEC Output : 2 groups of 9V output, (1 +9V pad on the front, +9V output in a seat on the back), the total current output is 2A 3.3V BEC Output : 1 group (1 3.3V pad on the front), the maximum current is 500mA 4.5V BEC Output : 2 groups (2 4.5V pads on the front), the maximum current is 1A ESC signal: M1-M4 on the back and M5-M8 on the front UART serial port: five groups of serial ports (UART1, UART2, UART3, UART4 , UART6) ESC telemetry input: R4 (UART4) I2C:Support. SDA, SCL pads on the front. For magnetometers, sonar, etc. Legacy Betaflight LED Pads: Supported. 5V, G, LED strip on the bottom of the front. For BF control WS2812 LED light Buzzer:Support .BZ+ , BZ- pad used for 5V buzzer BOOT key: Supporte.Press and hold the BOOT key to power on, you can enter the DFU mode, which is used to save the brick and flash the firmware; in the power-on standby state, the BOOT key is also used to control the LED strips connected to the D1-D4 pads on the four corners of the PCB. By default, short press the BOOT key to cycle through the LED display status; Changan BOOT key switches the LED control mode: for SpeedyBee LED or BF LED. In BF LED mode, these LED strips will be controlled by BF firmware RSSI pad:Support. Labeled as RS SmartPort:Support. You can use any set of serial port TX Supported flight controller firmware:BetaFlight (default), EMUFlight, INAV Firmware target name:for SPEEDYBEEF405V3 Mount:30.5x30.5mm (4mm hole diameter) Dimensions:41.6(L) x 39.4(W) x 7.8(H) mm Weight:9.6g for SpeedyBee BLS 50A 4-in-1 ESC Firmware:LHeli_S JH50 Wireless configuration:Full configuration supported by for SpeedyBee App PC configurator download link:ttps://esc-configurator.com/ Continuous Current:50A*4 Break current:55A (5S) Protective Diode for TV:Yes External Capacitor:1500uF Low ESR Capacitor (included in the package) Protocol ESC:DSHOT300/600 Power Input:3-6S LiPo Output power:VBAT Current sensor:Support (scale=386 offset=0) Mount:30.5x30.5mm (4mm hole diameter) Dimensions:45.6(L)*44(W)*6.1mm(H) Weight:13.8g
Price: 119.57 USD
Location: 中国
End Time: 2024-11-18T05:50:48.000Z
Shipping Cost: 0 USD
Product Images
Item Specifics
Restocking Fee: No
Return shipping will be paid by: Buyer
All returns accepted: Returns Accepted
Item must be returned within: 14 Days
Refund will be given as: Money back or replacement (buyer's choice)
Quantity: 1 pcs
Remote Control Peripherals/Devices: Remote Controller
Four-wheel Drive Attributes: Motors
RC Parts & Accs: Radio Systems
MPN: does not apply
Is Electric: No battery
Recommend Age: 14+y
Tool Supplies: Battery
Brand: Unbranded
Use: Vehicles & Remote Control Toys
Material: Composite Material
Origin: Mainland China
For Vehicle Type: Airplanes
