S1LD) 1968 SHELBY SEQUENTIAL DYNAMITE STICK Sequencer and LED Flashers

Description: California Proposition 65: WARNING: This product has not been tested for chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov All parts are new aftermarket replacement parts manufactured by Cougars Unlimited LLC and come with a 2-year limited factory warranty. They are replacement parts to be used to replace the original Ford parts used in there sequencing tail light systems on models that originally came with sequencing tail lights. They are made to plug and play into the original mounting and wiring harness. They are not designed to be used to convert non-sequencing tail light systems to sequencing tail lights. You are purchasing Cougars Unlimited LLC Dynamite stick sequencers (Pair L and R) used to replace the original Shelby Mustang Dynamite stick sequencers. And Two LED Electronic Flasher Cans, one for Turn Signals and one for Emergency Flashers. Included parts are: One pair S8MS-13A366-LK Dynamite stick sequencers (Note: Compatible with either LED or Incandescent bulbs) AND Two DOWY-13350-AR4 Electronic Flasher Can (LED bulbs only) Application: 1968 Shelby Mustang or Eleanor Mustang Replaces: Turn signal Dynamite stick sequencers, Flasher Can, and Emergency Flasher Can The Cougars Unlimited LLC DOWY-13350-AR5 electronic flasher is specifically designed to work with sequencing tail light turn signals. The on time is set to allow all three tail light bulbs to flash before turning off, much slower than a standard flasher can. Also, this flasher is designed to handle the current of all four incandescent bulbs (three rear and one front), standard flasher cans are typically only able to handle the current of two incandescent bulbs. With the exception of an added ground wire, they are made to plug and play into the original mounting and wiring harness. Because this is an electronic flasher the added ground wire must be securely grounded or the flasher will malfunction. Note: Cougars Unlimited LLC Electronic Flasher can application can be confusing. Here is a chart to try and clarify. All Flasher cans built by Cougars Unlimited LLC are Electronic replacing the original thermal cans. Shelby Mustang FLASHER CAN CHART 1968 - DOWY-13350-AR5 (Incandescent bulbs) 1968 - DOWY-13350-AR4 (LED bulbs) 1969 - DOWY-13350-AR5 (Incandescent bulbs) 1969 - DOWY-13350-L (LED bulbs) 1970- DOWY-13350-AR5 (Incandescent bulbs) 1970 - DOWY-13350-L (LED bulbs) NOTE: The 1968 Shelby LED flasher is different than the 1969 and 1970 Shelby LED flasher. Also, the 1968 1969 1970 Shelby Incandescent flasher is different than all the Cougars and Thunderbirds Incandescent flashers. NOTE: And yes, the 1968 Shelby LED flasher is the same as some the Cougars and Thunderbirds Incandescent flashers. 1968 Shelby Mustang PARTS CHART SEQUENCER TAILLIGHT DYNAMITE STICK S1L) S8MS-13A366-LK (LED or Incandescent bulbs) Flasher can electronic, Incandescent systems – S3) DOWY-13350-AR5 (Incandescent bulbs) Flasher can electronic, LED systems – S3L8) DOWY-13350-AR4 (LED bulbs) TURN SIGNAL SWITCH - WITH TILT – C48) C8SZ-13341-BR (*LED bulbs only) Harness repair pigtails, taillight side – S7) C5SZ-14405-P1 Harness repair pigtails, sequencer side – S8) C5SZ-14405-P2 Tail Light Harnesses with sockets (Pair, R and L) - S6) - C5SB-13407-AR *NOTE: TURN SIGNAL SWITCH – All turn signal switches sold by Cougars Unlimited LLC are for use with LED bulbs only. The reason for this is applicable vehicles are now over 50 years old the current that sequencing systems draw have greatly increased over time. This is because of the original wiring harnesses and connectors are deteriorating increasing the resistance. Higher the resistance the higher the current draw across the switch. The current is now so high on most vehicles that it exceeds the ratting of the switches, causing them to prematurely fail. The only solution is to convert to LED bulbs, they draw far less current. On vehicles that have converted to LED the turn signal switches are not failing. The only other solution is to replace the complete wiring harness which is expensive, and in most cases not possible. When converting to LED bulbs Cougars Unlimited LLC strongly recommends using WCCC1157RPR (Red for rear) LED bulbs and WCCC1157YPR (Yellow for front) LED bulbs. They have a built in current limiting diode. This stops the reverse current flow that causes sequential turn signal systems to malfunction.

Price: 307.95 USD

Location: Albuquerque, New Mexico

End Time: 2025-01-22T23:15:38.000Z

Shipping Cost: 0 USD